| EMG : PA2 (75 comments)Suitable for guitars and basses- Boost 0 - 20 dB- 1 Mini switch circuit |
|
| EMG : EXG Expander (28 comments)
Offers exceptional tonal flexibility- Similar frequency response to a typical guitar amp e...(+) Offers exceptional tonal flexibility- Similar frequency response to a typical guitar amp equaliser with a boost in the lows and highs and a cut in the mids as you turn the knob- Full sound that doesn't get muddy and keeps the sound clean and clear- Excellent for P90s and humbuckers- Includes output jack and battery clip set |
|
| EMG : EXB Bass Expander
EMG EXB Bass Expander; unconventional Equalization control for Bass that increases the low...(+) EMG EXB Bass Expander; unconventional Equalization control for Bass that increases the low and high frequency regions while reducing the Midrange; provides the Clear Gain and Percussive Punch that especially Slap Bass players will appreciate; incl. Output Jack and Battery Clip set, Note: only suitable for EMG pickups |
|
| EMG : RPC Peak Control (7 comments)
Axle: Fluted- Thread length: 10.2 mm- Thread diameter: 8 mm- Housing diameter: 24.8 mm- In...(+) Axle: Fluted- Thread length: 10.2 mm- Thread diameter: 8 mm- Housing diameter: 24.8 mm- Incl. output jack and battery clip set- Made in USA |
|
| EMG : 25k-LH Volume Pot (Solderless) (2 comments)
For left-handed electric guitar and electric bass models- Resistance: 25 kOhm- Resistance ...(+) For left-handed electric guitar and electric bass models- Resistance: 25 kOhm- Resistance curve: Anti-logarithmic- Solderless connection- Knurled shaft- Shaft diameter: 6 mm- Shaft length: 10 mm- Thread length: 9 mm- Thread diameter: 8 mm- Housing diameter: 25 mm- Includes a solderless cable set |
|
| EMG : 25k-LH Tone Pot (Solderless) (3 comments)
For left-hand electric guitar and electric bass models- 25 kOhm resistor- Antilogarithmic ...(+) For left-hand electric guitar and electric bass models- 25 kOhm resistor- Antilogarithmic resistance curve- Solderless connection- Knurled shaft- Diameter shaft: 6 mm- Shaft length: 10 mm- Thread length: 9 mm- Diameter of thread: 8 mm- Diameter of case: 25 mm- Solderless cable set included |
|
| EMG : CBL-COAX 3P/2P/1P 15" (29 comments)
EMG cable- 3-pole EMG Solderless plug-in connection on one side and 2-pole + 1-pole EMG So...(+) EMG cable- 3-pole EMG Solderless plug-in connection on one side and 2-pole + 1-pole EMG Solderless plug connections on the other- For connecting active EMG pickups to guitars or bass electronics with EMG's Solderless System- Length: 38 cm (15 ") |
|
| EMG : CBL-Quik Connect Cable
EMG cable- 3-pole EMG Solderless plug connection on one side and bare wires on the other- ...(+) EMG cable- 3-pole EMG Solderless plug connection on one side and bare wires on the other- For soldering active EMG pickups to guitars or bass electronics without EMG's Solderless System- Length: 370 mm |
|
| EMG : CBL-5P/2P 15.5" (4 comments)
EMG HZ cable- 5-Pin EMG solderless connector on one side and 2-pin EMG solderless connecto...(+) EMG HZ cable- 5-Pin EMG solderless connector on one side and 2-pin EMG solderless connector on the other- For connecting passive (HZ) EMG pickups to guitars or bass electronics with EMG's solderless System- Length: 393 mm |
|
| EMG : CBL-HZ Quik Connect Cable (22 comments)
EMG HZ cable- 5-Pin EMG solderless connector on one side and bare wires on the other- For ...(+) EMG HZ cable- 5-Pin EMG solderless connector on one side and bare wires on the other- For hard wiring (soldering) passive (HZ) EMG pickups to guitars or bass electronics without EMG's solderless System- Length: 380 mm |
|