| Walrus Audio : ACS 1 Amp+Cab Simulator
(21 comments)
Pour guitare électrique- Simulateur d'amplificateur/baffle- 3 modèles d'amplificateurs b...(+) Pour guitare électrique- Simulateur d'amplificateur/baffle- 3 modèles d'amplificateurs basés sur des combos classiques de l'histoire de la musique britannique et américaine- Option double amplification: 2 différentes combinaisons amplificateur/baffle possibles pour les canaux gauche et droit- 6 réponses impulsionnelles de baffles de haute qualité sélectionnables et adaptées aux amplificateurs individuels- Chargement de réponses impulsionnelles utilisateur via l'application web gratuite- Simulation de pièce pour une sensation authentique- 3 presets intégrés (jusqu'à 128 via MIDI)- Fonction Boost: Commute le volume et/ou le gain à une valeur prédéterminée- Convertisseurs A/N et N/A haute résolution 24 bits/48 kHz- Traitement interne à virgule flottante 32 bits- Contrôles: Bass, Mid, Treb, Vol, Gain, Room- Commutateurs: Cab, L+R, Fullerton/London/Dartford- Commutateurs au pied: Bypass, Boost- LEDs de statut multicolores- Sortie casque sur mini Jack stéréo 3,5 mm- 2 entrées mono/stéréo sur Jack 6,3 mm- 2 sorties mono/stéréo sur Jack 6,3 mm- MIDI In/Out sur prises DIN- Port USB pour chargement de réponses impulsionnelles et mises à jour du firmware- Fonctionne avec un bloc d'alimentation 9 V DC (polarité négative à l'intérieur) optionnel non-fourni- Consommation min.: 300 mA- Dimensions avec potentiomètres (LxPxH): 67 x 124 x 64 mm- Poids: 540 g- Fabriquée aux USA |
|
| Walrus Audio : Canvas Re-Amp
(1 comments)
Pedal format- Converts the impedance of an audio signal from an audio interface to suit gu...(+) Pedal format- Converts the impedance of an audio signal from an audio interface to suit guitar effects and amps- Already recorded audio signals can be processed afterwards with the preferred combination of pedals and guitar amplifiers- Specially wound "custom" transformers for best sound quality and low distortion factor- Adjustable output volume- Switchable ground lift to avoid hum loops- Linear frequency response: 20 - 20,000 Hz- Switches: ground lift, phase, mute, HPF (high-pass filter)- Control: Volume- Inputs: 6.3 mm mono jack, XLR female- Output: 6.3 mm mono jack- Dimensions (L x W x H): 12.1 x 6.6 x 3.6 cm- Weight: 345 g- Passive design - no power supply necessary- Made in the USA |
|
| EB-10 Preamp/EQ/Boost
Black. Walrus Pedals. General Merchandise. Hal Leonard #900-1049B. Published by Hal Leonar...(+) Black. Walrus Pedals. General Merchandise. Hal Leonard #900-1049B. Published by Hal Leonard (HL.323220).
Item Number: HL.323220
ISBN 1540070670. 4.25x5.5 inches.
A tone tweakers delight, the EB-10 works as a preamp, EQ and boost to meticulously craft your guitar's sound, allowing for studio-grade electric guitar tone in a live setting. Each rotary knob offers up to 12dB of boost OR cut of low, mid, and high frequencies, based on where you have the toggle switches set. When the Boost switch is engaged, add a 10dB MOSFET boost for some great extra punch.
Use the EB-10 to compensate when switching between low and high output instruments. Push through the mix during solos, or even use the onboard presets as three different gain stages by using combinations of increasing boosted EQ settings and the Boost switch! With nine different EQ positions on each knob, bring out new tonal characteristics you didn't know your guitar or bass even had.
The EB-10 offers two operating modes, Live and Preset. In live mode, the pedal responds to current position of all the knobs and switches. Dial in a specific sound and turn the pedal on and off with the Bypass switch. In preset mode, the pedal offers preset slots to store three unique sounds. When in preset mode, the pedal is locked on and the user can scroll through the presets by clicking the Bypass switch. The pedal will boot up in the last known operating mode and if that is preset mode, it loads preset 1 by default. Enter preset mode by pressing and holding the bypass switch for 3 seconds until you see the preset light P1 turn on. Repeat to exit. You are in live mode when all preset lights are off. Refer to the manual on saving presets.
A portion of proceeds from each pedal sold will be donated to www.raicestexas.org.
SPECS:
The EB-10 comes coated in Prismatic Powders, Matte Black and Cream enclosures with art inspired by vintage studio equipment. Design by Tyler Evans.
The die-cast enclosure's exact size is 3.68″ x 4.67″ x 1.547″. Power requirements are 9VDC, center negative (100mA minimum).
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals. Daisy chain power supplies are not recommended. Power supply not included. |
|
| EB-10 Preamp/EQ/Boost
Cream. Walrus Pedals. General Merchandise. Hal Leonard #900-1049C. Published by Hal Leonar...(+) Cream. Walrus Pedals. General Merchandise. Hal Leonard #900-1049C. Published by Hal Leonard (HL.323221).
Item Number: HL.323221
4.25x5.5 inches.
A tone tweakers delight, the EB-10 works as a preamp, EQ and boost to meticulously craft your guitar's sound, allowing for studio-grade electric guitar tone in a live setting. Each rotary knob offers up to 12dB of boost OR cut of low, mid, and high frequencies, based on where you have the toggle switches set. When the Boost switch is engaged, add a 10dB MOSFET boost for some great extra punch.
Use the EB-10 to compensate when switching between low and high output instruments. Push through the mix during solos, or even use the onboard presets as three different gain stages by using combinations of increasing boosted EQ settings and the Boost switch! With nine different EQ positions on each knob, bring out new tonal characteristics you didn't know your guitar or bass even had.
The EB-10 offers two operating modes, Live and Preset. In live mode, the pedal responds to current position of all the knobs and switches. Dial in a specific sound and turn the pedal on and off with the Bypass switch. In preset mode, the pedal offers preset slots to store three unique sounds. When in preset mode, the pedal is locked on and the user can scroll through the presets by clicking the Bypass switch. The pedal will boot up in the last known operating mode and if that is preset mode, it loads preset 1 by default. Enter preset mode by pressing and holding the bypass switch for 3 seconds until you see the preset light P1 turn on. Repeat to exit. You are in live mode when all preset lights are off. Refer to the manual on saving presets.
A portion of proceeds from each pedal sold will be donated to www.raicestexas.org.
SPECS:
The EB-10 comes coated in Prismatic Powders, Matte Black and Cream enclosures with art inspired by vintage studio equipment. Design by Tyler Evans.
The die-cast enclosure's exact size is 3.68″ x 4.67″ x 1.547″. Power requirements are 9VDC, center negative (100mA minimum).
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals. Daisy chain power supplies are not recommended. Power supply not included. |
|
